Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Canarsie Homeowners
A missing or cracked chimney cap is the reason water gets into a Canarsie chimney, and it’s the most common problem we find on the roofs here. Our chimney cap & crown work covers the full top of the stack: fitting a new cap, replacing a failed one, rebuilding a cracked crown, and coating a crown that’s still sound but starting to break down. Our technicians have up to 8 years of experience and handle the whole job, so the crew that inspects is the crew that repairs. We name the exact cap and crown materials before the estimate is written, so you know what’s going on your roof. Call (833) 508-9953 to book an assessment.

What Our Chimney Cap & Crown Service Includes
Every job starts on the roof, because that’s where the answer is. We look at how the cap is sitting, whether the mesh has rusted through, whether the crown has pulled away from the flue, and whether water has started to track down the brick. Then we match the fix to what we actually see. You’ll get a clear description of the work and a flat price before anything is ordered or set in motion.
Cap Installation
A chimney cap is the cover that sits over the flue and keeps rain, snow, birds, squirrels and leaves out of the flue. If your Canarsie home has an open flue top, that opening is an invitation for water and animals, and it also lets downdrafts push smoke back into the house. We install a cap sized to your flue, with a mesh screen fine enough to stop birds and sparks but open enough to let smoke out freely, and we anchor it so wind off the open ground near the Belt Parkway corridor doesn’t work it loose.
Cap Replacement
Replacement makes sense when a cap is still on the chimney but no longer doing its job: rust-through on the screen, a bent or missing lid, a cap that’s been torn loose by a storm, or a cap perched on a flue it was never sized for. A cap that’s rusting or wobbling will eventually drop or blow off, and water gets a straight shot down the flue either way. We pull the old cap, check the top of the flue for damage, and fit a new one with the correct sizing and fastening.
Crown Repair
The crown is the concrete or mortar slab at the very top of the chimney, sloped so water runs away from the flue instead of into it. When the crown cracks, water gets between the crown and the flue and starts soaking the brick and mortar below, which shows up later as spalling brick, rusted damper parts and staining on interior walls. We repair crowns by removing the failed material, rebuilding the slope so it sheds properly, and bonding it back to the flue so there’s no seam for water to find.
Crown Coating
Coating is the right call when a crown is structurally sound but its surface is checking, pitted, or shedding grit. A proper crown coating seals that surface and holds off the freeze-thaw damage that eats crowns in this climate, where a wet crown that freezes overnight can crack and split long before the slab itself fails. We prep the surface, coat it, and leave you with a crown that sheds water again instead of absorbing it. If the crown is too far gone for coating, we’ll say so rather than coat a slab that’s already failing.
Multi-Flue Cap
A multi-flue cap is a single cover that spans two or more flues side by side, common on Canarsie houses where a heating flue and a fireplace flue share one stack. Multiple single caps on that kind of stack can interfere with each other or leave gaps between them, and the gaps are where water gets in. We size one cap to cover the whole top, keep each flue drawing properly, and fit it so it clears the crown and sheds water off the sides rather than pooling.
Custom Cap
Some stacks don’t fit a standard size: an oversized flue, an off-center crown, a wide masonry top, or a shape that a stock cap can’t cover cleanly. We build a custom cap to fit the actual dimensions and match the look of the house, because a cap that’s too small or badly seated causes its own water and draft problems. We measure on site and fabricate to those measurements, so the finished cap sits level and covers everything it needs to.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with Gelco and Famco caps and covers because these are brands chimney professionals specify, not whatever the hardware aisle happens to stock. A cap from a known line has a known mesh gauge, known lid thickness and known fastening, and when something wears out we know where to look. When a job calls for a custom-fabricated cover, we work from specifications we can stand behind, and we tell you the name on the box before it goes up.
We also work with Olympia Chimney and Copperfield components where they suit the stack. Our technicians have up to 8 years of experience and have seen how these products hold up on Canarsie roofs through wet winters, freeze-thaw cycles and summer storms. Whether you have a Gelco cap that needs replacing, a Famco cover that’s been knocked loose, or any other make, we can help. If you’re not sure what’s up there, our chimney sweep canarsie service starts with a look at the whole system, top to bottom.
Signs You Need Chimney Cap & Crown Right Now
Some of these you can see from the ground with binoculars. Some you’ll only notice once the damage has already moved inside the chimney. Here’s what to watch for.
- Water stains on the ceiling or chimney breast. Brown rings or damp patches near the chimney usually mean water is getting past the crown or cap and tracking down the masonry. The stain is the last thing to show up, not the first, which is why it’s worth a look before you see it.
- Crumbling mortar or brick at the top of the stack. Spalling brick and washed-out joints near the crown point to water getting in at the top and freezing in the masonry. Fix the source and the brick can dry out; leave it and the damage keeps climbing down the stack.
- Rust, a bent lid, or a missing cap. A cap that’s rusted through, sagging, or gone altogether stops doing its job the day it fails. Replacing a cap is simple work compared to repairing a flue that’s been taking rain for a season.
- Birds, squirrels or nesting debris in the flue. An open or broken cap lets animals in, and nest material in a flue is both a draft problem and a fire risk. If you’ve had a bird show up in the firebox, the cap is the first thing to check.
- A visible crack in the crown. Hairline cracks grow, and a crack wide enough to catch a fingernail is already letting water in. Catching a crown at that stage is a coating or a repair instead of a rebuild.
Our Chimney Cap & Crown Process – Step by Step
We keep the process plain, because nobody likes guesswork on a roof they can’t see.

- 1
Roof-level inspection. We get up to the stack and look at the cap, the crown, the flue and the flashing with our own eyes, and photograph what we find. No recommendation gets made from the ground.
- 2
Show you the evidence. We walk you through the photos and explain what each one shows, in plain language. You see the cracked crown or the rusted screen yourself, so you’re not taking anyone’s word for it.
- 3
Written flat-price estimate. You get the price for the work in writing, per job, before we begin. If we find something that needs a look further down the flue, we’ll take a camera view and show you that too before recommending anything.
- 4
Do the work. Cap, crown, coating or custom fabrication, done with the material matched to the job and fitted properly. We protect the roof and the surrounding area while we’re up there and clean up after ourselves.
- 5
Final check and a look at the finished job. We confirm the cap is seated and fastened, the crown sheds water the way it should, and we leave you photos of the finished work. You’ll know exactly what’s protecting your chimney.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Canarsie?
A single-flue cap installation in Canarsie typically runs $250 – $600, depending on the flue size, the cap style and how much repair the top of the stack needs before the cap goes on. A multi-flue or custom cap generally falls in the $500 – $1,200 range, since fabrication and the wider span add cost. Crown repair usually runs $400 – $1,000 depending on how much material has to come out and be rebuilt, while a crown coating is the lower-cost option at roughly $350 – $750 when the crown is sound enough to coat.
A few things move those numbers. A steep or hard-to-access roof takes more time and care than a gently pitched one. A crown that’s cracked all the way through costs more to fix than one that’s only surface-checked, because rebuilding the slope is more work than sealing it. A cap on an odd-sized stack that needs custom fabrication costs more than a standard size. And if the flue itself turns out to be damaged underneath, that’s a separate conversation with its own estimate, and we’ll tell you plainly if it can wait.
What keeps you from overpaying is the flat-price estimate: the price is set per job from that written estimate, and nothing gets recommended that we can’t show you in a photo. The estimate itself is free. Our chimney cap & crown service is one of five we handle under this roof, alongside sweeping, inspection, chimney repair and fireplace repair, so no second contractor gets called in for the fix.
Chimney Cap & Crown Near Canarsie – Our Service Area
We cover Canarsie and the surrounding neighborhoods, including chimney cap & crown work in East New York, Brownsville, Marine Park, Mill Basin, Bergen Beach, East Flatbush, Flatlands and Crown Heights, with chimney cap & crown jobs in Brownsville following the same process. We answer 24/7, and dispatch runs 7am to 7pm, Sunday through Friday, with same-day appointments where the schedule allows.
Serving Canarsie, NY – Our Local Coverage Area
We serve Canarsie and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Canarsie
A cap is the cover over the top of the flue that keeps rain, snow and animals out; the crown is the sloped slab of mortar or concrete at the top of the chimney that sheds water away from the flue. Together they’re the first line of defense against water getting into the chimney. Most water intrusion we find in Canarsie starts at one of these two places. If yours are compromised, that’s the place to start, and a free estimate will tell you what’s needed.
Most cap installations and crown coatings finish in a few hours on site. A crown rebuild takes longer, sometimes into a second visit, because the mortar has to be worked and finished properly. Custom caps take time to fabricate, so there’s a lead time before installation day. We’ll give you a realistic timeline with the estimate, not a guess.
A single-flue cap typically runs $250 – $600, a multi-flue or custom cap $500 – $1,200, a crown coating around $350 – $750, and a crown repair $400 – $1,000 depending on how much has to be rebuilt. The written estimate sets the final price, and the estimate is free. Call (833) 508-9953 for an exact quote – estimates are free.
Yes. We work with Gelco and Famco caps, Olympia Chimney components and Copperfield covers, and we know where each tends to wear. If you have a cap from one of these lines that’s failing, we can replace it with the same type or a better fit. Whatever brand is on your stack now, we can help.
Same-day appointments are available when the schedule allows, so call and we’ll tell you what’s open. We answer 24/7, and dispatch runs 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening.
The local pro stands behind the materials specified on the estimate and the workmanship described in it. We don’t make blanket guarantees that aren’t written down, so anything specific to your job will be explained on the estimate before you agree to it. Ask us directly and we’ll tell you exactly what’s covered.
Nothing much is needed from you. Clear access to the chimney from inside the house helps, and if we’re inspecting the flue, make sure the fire is out and cold for at least a day before we arrive. Move anything fragile away from the fireplace and let us know about pets or gate codes. The roof work itself is on us.
Schedule Your Chimney Cap & Crown Service in Canarsie Today
Chimney problems don’t get cheaper when you wait, and the top of the stack is where most of them start. Call (833) 508-9953 to book a free, no-obligation estimate in Canarsie. We’ll show you what’s wrong with photos, give you a flat price per job, and tell you honestly if the work can wait. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Canarsie.