Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Canarsie Homeowners
Canarsie’s brick chimney stacks take a beating. Between the freeze-thaw cycles that work moisture into mortar joints and the wind-driven rain that gets past a worn crown, the masonry on an older Canarsie home rarely fails all at once. It crumbles a little each season, and by the time a homeowner sees a stain on the ceiling or a loose brick on the roof, water has usually been getting in for a while. That’s the reason we treat chimney repair as a diagnostic job first: a sweep without an inspection is a missed diagnosis. Our technicians have up to 8 years of experience, and we work with professional-grade materials from names like HeatShield and Olympia Chimney because professionals don’t cut corners on what goes back into your flue. When a repair can’t wait, we offer same-day service in Canarsie. Call (833) 508-9953 to book a visit.

What Our Chimney Repair Service Includes
Chimney repair covers the masonry, the flue interior, and the metalwork that keeps water out. We handle all of it as one job instead of sending you to a mason, then a roofer, then a liner company. These are the six repairs we do most often in Canarsie.
Mortar Repointing
Repointing is the replacement of the soft, crumbled mortar between bricks while the bricks themselves stay in place. You need it when joints have receded enough that you can catch a fingernail in them, or when the mortar turns sandy and washes down the roof in the rain. We grind out the failed joints to a consistent depth and pack in fresh mortar matched to the existing color and hardness, so the new work doesn’t push the old brick around.
Spalling Brick Repair
Spalling is when the face of a brick flakes or pops off, usually because the brick has absorbed water and the freeze finally cracked it. You’ll spot it as brick dust on the roof, a scalloped face on the stack, or chunks of brick in the gutter. We cut out the failed units and replace them with brick of matching size and absorption, then repoint around them. Patching over a spalled face with mortar just traps the moisture that caused it.
Chimney Waterproofing
Waterproofing is a breathable sealer applied to the masonry so rain beads off while vapor inside the chimney can still escape. It’s the right call for any Canarsie chimney with sound brick but a history of damp patches or efflorescence, that white powder that leaches out of masonry. We apply it after repairs are finished and cured, never over failing mortar, because sealing a cracked joint only locks the water inside.
Flashing Repair
Flashing is the metal where the chimney meets the roof, and it’s the joint most likely to leak without anyone noticing. You need it looked at when you see staining on the ceiling near the chimney, rust streaks on the stack, or visible gaps where the metal lifts away from the shingles. We reset or replace the flashing and seal the counterflashing into the masonry so the roof-to-chimney seam sheds water the way it should.
Chimney Rebuilding
Rebuilding is for a stack that has gone past repointing, typically when a whole course of brick has moved, the crown is collapsing, or the top few feet are loose enough to be a hazard. That’s a structural job and it belongs to a trained mason, not a homeowner on a ladder. We rebuild from a sound base up, matching the original footprint and adding a proper crown and cap so the new masonry is protected from day one.
Tuckpointing
Tuckpointing is the fine finish work of filling and shaping joints so the mortar lines read clean and even across the face of the chimney. It’s used on visible stacks where the look of the masonry matters as much as the seal, and on older Canarsie homes where a mismatched patch job would stand out from the street. We shape each joint by hand and match the mortar to the surrounding brick so the repair blends in rather than announcing itself.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
When a chimney needs a new liner or a venting component, the material matters as much as the labor. We install and work with DuraFlex flexible liner systems, and we know how that product behaves when it’s pulled down a flue with an offset or a rough interior. A flexible liner that’s sized wrong will kink on the way down and never sit right, so we measure the flue first.
We’re also certified applicator-level familiar with HeatShield, the flue resurfacing system that repairs a damaged interior without a full liner replacement, and we source caps and covers from Gelco, Famco and Copperfield, brands that chimney professionals specify rather than consumer retail lines. We name what we install so you know exactly what’s protecting your home. Whether you have DuraFlex, HeatShield, Olympia Chimney components or any other make, we can help.
Signs You Need Chimney Repair Right Now
- Crumbling mortar joints. If the mortar between bricks recedes or turns to sand, water has a direct path into the masonry. Left alone, it works its way inward and starts pushing bricks loose. Repointing at this stage is a small job; waiting turns it into a rebuild.
- White staining or dark patches on the brick. That chalky white bloom, or a dark damp band on the stack, means moisture is moving through the masonry. Catching it early usually means waterproofing and a flashing check rather than structural work.
- Water stains on the ceiling or chimney breast. Brown rings near the chimney almost always trace back to flashing, a failed crown, or a missing cap. The chimney is the first place to look, even when the stain shows up on an interior wall.
- Loose or missing bricks. A brick that has shifted, dropped out, or sits proud of the stack is a structural concern, not a cosmetic one. Keep people off the roof and off the ground below the chimney, and have it assessed by a trained professional.
- Rust on the damper or firebox. Rust inside the fireplace means water is getting down the flue, usually from an open top or a failed crown. Moisture in the firebox will eventually reach the damper and the surrounding metal.
Our Chimney Repair Process – Step by Step
- 1
Inspection before any recommendation. We start by looking at the whole system: the firebox, the damper, the flue interior, the crown, the flashing and the masonry. Where the flue is concerned, we use a camera so we can see the condition of the interior joints and any cracks, not just guess at them. Nothing gets recommended until there’s evidence to point to.
- 2
A written scope and price. You get the findings in plain language with photos, and a written estimate that sets the final price. If part of the work can safely wait a season, we’ll tell you that too, rather than bundling everything into one invoice.
- 3
Repairs done in the right order. Water entry gets stopped first, then the masonry is repaired, then the flue interior is addressed, then the crown and cap go back on top. Doing it in that sequence is what keeps the new work from being undone by the next rain.
- 4
Materials matched to the job. We mix mortar to match the existing brick’s hardness, and use professional-grade materials where they’re called for, including HeatShield for flue resurfacing and DuraFlex liners where a full liner is the right answer. Hardware-store substitutes are cheaper for a reason.
- 5
A final look and a clean roof. We photograph the finished work, check the flashing seam and the crown, and clear the debris off the roof and out of the yard. You get the report, so you have a record of what was done and what to keep an eye on.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Canarsie?
Chimney repair in Canarsie is priced per job, and the range is wide because a flashing repair and a rebuild have almost nothing in common. Here are typical estimates for the work we do most often. The written estimate always sets the final price.

| Repair | Typical Estimated Range |
|---|---|
| Mortar repointing | $450 – $1,200 |
| Tuckpointing (finish work) | $500 – $1,400 |
| Spalling brick replacement | $600 – $1,800 |
| Flashing repair | $350 – $900 |
| Chimney waterproofing | $300 – $700 |
| Chimney rebuild (upper stack) | $3,000 – $8,000 |
What moves the number is how much of the chimney is affected, the height and pitch of the roof, whether scaffolding is needed, and whether the flue interior also needs work. The way to avoid overpaying is to get the findings in writing with photos before you agree to anything, and to ask what can safely wait. Every estimate we give is free and includes a camera inspection with a photo report you can look at yourself. You shouldn’t have to take anyone’s word for a repair you can’t see.
Chimney Repair Near Canarsie – Our Service Area
We work throughout Canarsie and the neighborhoods around it, including East New York, Brownsville, Flatlands, Marine Park, Mill Basin, Bergen Beach, East Flatbush, Flatbush, Crown Heights, Cypress Hills and Bedford-Stuyvesant. Travel time within this pocket of Brooklyn is short, so we can usually schedule a visit quickly once you call. If you’re in a neighboring area and need chimney repair, the same crew and the same process apply. For the full range of what we do, start at Chimney Sweep Canarsie or go straight to the chimney repair page.
Serving Canarsie, NY – Our Local Coverage Area
We serve Canarsie and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Canarsie
Chimney repair covers the fixes that restore a chimney’s structure and keep water out: repointing and tuckpointing failed mortar, replacing spalled brick, sealing the masonry, repairing flashing, and rebuilding a stack that’s gone too far. It’s separate from sweeping, which removes creosote, and from inspection, which tells you what condition the system is in. Chimney Sweep Canarsie does all three, so the same company that finds a problem is the one qualified to fix it. Call (833) 508-9953 to book an inspection that starts the process.
Most repairs take a single visit. Repointing, flashing work and waterproofing are typically done in one day, while a spalling brick repair or tuckpointing job may run into a second depending on how much of the stack is involved. A rebuild takes longer, usually several days, because the mortar needs time to cure before the crown and cap go back on. We give you the timeline in writing with the estimate so you know what to expect.
Typical estimates in Canarsie run from about $300 to $700 for waterproofing and $450 to $1,200 for repointing, with flashing repair around $350 to $900 and an upper-stack rebuild in the $3,000 to $8,000 range. The final cost depends on how much of the chimney is affected, roof access, and whether the flue interior needs resurfacing as well. The written estimate sets the price, and the estimate itself is free. Call (833) 508-9953 for an exact quote.
Yes. We’re certified applicator-level familiar with HeatShield, the flue resurfacing system that repairs a damaged interior without a full liner replacement, and we install DuraFlex flexible liner systems when a flue needs a new liner. We also work with Olympia Chimney components and source caps and covers from Gelco, Famco and Copperfield. Whether you have these or any other make, we can help.
Yes, we offer same-day service in Canarsie when the schedule allows. We answer 24/7, and dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed on Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (833) 508-9953 to get on the schedule.
We stand behind the work we do, and every job comes with a written estimate that spells out the scope before anything starts. If you’re comparing bids, ask each one what materials go in and whether an inspection report with photos is included, because that’s where cheap quotes usually cut corners. We’re happy to walk you through what our estimate covers, line by line. Call (833) 508-9953 with any questions before you book.
Clear the area around the fireplace and make sure we can get to the roof access point, whether that’s a hatch, a window or a ladder. If you’ve noticed staining, note where it is and when it first appeared, since that helps us trace the source. Keep pets and children away from the work area while we’re on site. Beyond that, there’s nothing to do; the inspection, the photos and the estimate are all part of the visit.
Schedule Your Chimney Repair Service in Canarsie Today
Chimney problems don’t get cheaper when you wait. A joint that needs repointing this year can become a stack that needs rebuilding in a few more, and the difference in cost is significant. We’ll inspect the chimney, show you what we find with photos, and give you a written estimate that sets the final price. No obligation, and we’ll tell you plainly when work can wait. Call (833) 508-9953. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Canarsie.